- Process Name:
- MIOEq™ 6 Band
- Synopsis:
- 6 band Fully Parameteric EQ
- Process Types:
-
EQ,
Mastering
- Channels:
- 2
- Description:
- MIOEq� 6 Band implements a stereo 6-band IIR EQ processor. Each band is fully parameteric, and can be set
to any of the filter types. All the parameters of all the bands can be set to any of valid settings.
The composite EQ curve is applied to the input signal, and the master gain is then applied to the
processed signal. The same EQ curve and gain are applied to both channels.
- Parameters:
- Enable {Off, On}
-
Enables the EQ block. When disabled, the EQ (including the master gain) is hard-bypassed,
and does not consume DSP power.
- Gain [-80, 10] dB
-
Master gain applied to the signal at the output of the EQ block. Since the EQ is implemented
as a high-resolution floating point process, you can bring the output signal of the EQ out of
any degree of clipping using this parameter.
- Band 1 Enable {Off, On}
-
Enables the band. When disabled, the band is hard-bypassed.
- Band 1 Gain [-24, 24] dB
-
Sets the parameteric gain on the EQ band. For peaking filters, this is the gain at the peak of
the band. For shelving filters, this is the gain at the extreme limit of the filter. This
parameter is ignored for the high and low pass filter types as well as the bandpass filter type.
- Band 1 Frequency [20, 22k] Hz
-
Sets the characteristic frequency of the filter band.
- Band 1 Bandwidth [0.01, 2.5] Oct
-
Sets the bandwidth of the filter band in octaves.
- Band 1 Type {Peaking/Parametric, Low Shelf, Hi Shelf, Hi Cut, Low Cut, Band Pass}
-
Chooses the type of filter that is applied for the band.
- Band 2 Enable {Off, On}
-
Enables the band. When disabled, the band is hard-bypassed.
- Band 2 Gain [-24, 24] dB
-
Sets the parameteric gain on the EQ band. For peaking filters, this is the gain at the peak of
the band. For shelving filters, this is the gain at the extreme limit of the filter. This
parameter is ignored for the high and low pass filter types as well as the bandpass filter type.
- Band 2 Frequency [20, 22k] Hz
-
Sets the characteristic frequency of the filter band.
- Band 2 Bandwidth [0.01, 2.5] Oct
-
Sets the bandwidth of the filter band in octaves.
- Band 2 Type {Peaking/Parametric, Low Shelf, Hi Shelf, Hi Cut, Low Cut, Band Pass}
-
Chooses the type of filter that is applied for the band.
- Band 3 Enable {Off, On}
-
Enables the band. When disabled, the band is hard-bypassed.
- Band 3 Gain [-24, 24] dB
-
Sets the parameteric gain on the EQ band. For peaking filters, this is the gain at the peak of
the band. For shelving filters, this is the gain at the extreme limit of the filter. This
parameter is ignored for the high and low pass filter types as well as the bandpass filter type.
- Band 3 Frequency [20, 22k] Hz
-
Sets the characteristic frequency of the filter band.
- Band 3 Bandwidth [0.01, 2.5] Oct
-
Sets the bandwidth of the filter band in octaves.
- Band 3 Type {Peaking/Parametric, Low Shelf, Hi Shelf, Hi Cut, Low Cut, Band Pass}
-
Chooses the type of filter that is applied for the band.
- Band 4 Enable {Off, On}
-
Enables the band. When disabled, the band is hard-bypassed.
- Band 4 Gain [-24, 24] dB
-
Sets the parameteric gain on the EQ band. For peaking filters, this is the gain at the peak of
the band. For shelving filters, this is the gain at the extreme limit of the filter. This
parameter is ignored for the high and low pass filter types as well as the bandpass filter type.
- Band 4 Frequency [20, 22k] Hz
-
Sets the characteristic frequency of the filter band.
- Band 4 Bandwidth [0.01, 2.5] Oct
-
Sets the bandwidth of the filter band in octaves.
- Band 4 Type {Peaking/Parametric, Low Shelf, Hi Shelf, Hi Cut, Low Cut, Band Pass}
-
Chooses the type of filter that is applied for the band.
- Band 5 Enable {Off, On}
-
Enables the band. When disabled, the band is hard-bypassed.
- Band 5 Gain [-24, 24] dB
-
Sets the parameteric gain on the EQ band. For peaking filters, this is the gain at the peak of
the band. For shelving filters, this is the gain at the extreme limit of the filter. This
parameter is ignored for the high and low pass filter types as well as the bandpass filter type.
- Band 5 Frequency [20, 22k] Hz
-
Sets the characteristic frequency of the filter band.
- Band 5 Bandwidth [0.01, 2.5] Oct
-
Sets the bandwidth of the filter band in octaves.
- Band 5 Type {Peaking/Parametric, Low Shelf, Hi Shelf, Hi Cut, Low Cut, Band Pass}
-
Chooses the type of filter that is applied for the band.
- Band 6 Enable {Off, On}
-
Enables the band. When disabled, the band is hard-bypassed.
- Band 6 Gain [-24, 24] dB
-
Sets the parameteric gain on the EQ band. For peaking filters, this is the gain at the peak of
the band. For shelving filters, this is the gain at the extreme limit of the filter. This
parameter is ignored for the high and low pass filter types as well as the bandpass filter type.
- Band 6 Frequency [20, 22k] Hz
-
Sets the characteristic frequency of the filter band.
- Band 6 Bandwidth [0.01, 2.5] Oct
-
Sets the bandwidth of the filter band in octaves.
- Band 6 Type {Peaking/Parametric, Low Shelf, Hi Shelf, Hi Cut, Low Cut, Band Pass}
-
Chooses the type of filter that is applied for the band.
- Master Bypass {On, Off}
-
Disables the EQ block. When disabled, the EQ (including the master gain) is hard-bypassed,
and does not consume DSP power.
- See also:
- MIOEq™ 6 Band (m/m),
MIOEq™ 12 Band (m/m),
MIOEq™ 12 Band (s/s)
Documentation Copyright © 2005, Metric Halo. All rights reserved.
